Published On Premiered Dec 15, 2020
Video này mình hướng dẫn cấu hình và test mạng CC-LINK của PLC Mitsubishi dòng Q. Module QJ61BT11N dùng để cấu hình Master or Local station.
In this video, I guide the configuration and test of CC-LINK network of PLC Mitsubishi MELSEC-Q series. Module QJ61BT11N is used to configure Master or Local station.
Automation | Mitsubishi
1. GX Works2 : Installation & Simulator - P1 I Cài đặt và chạy mô phỏng PLC Mitsubishi 👇
• GX Works2 : Installation & Simulator ...
2. How to install GT Designer3, HMI Mitsubishi - P2 | Cài đặt phần mềm lập trình HMI Mitsubishi 👇
• How to install GT Designer3 software ...
3. How to Upload & Download program Mitsubishi FX3U PLC by GX Works2 - P3 | Upload và Download PLC FX 👇
• GX Works2: How to Upload & Download p...
4. GT Designer3: Upload and Download program HMI GOT2000 by USB cable - P4 👇
• GT Designer3: Upload and Download pro...
5. GT Designer3: Upload and Download program HMI GOT2000 by Ethernet cable - P5 👇
• GT Designer3: Upload and Download pro...
6. GX Works2: Upload & Download program Mitsubishi PLC MELSEC-Q Series by ethernet cable - P6 👇
• GX Works2: Upload & Download program ...
7. How to connect GOT2000 HMI with MELSEC-F Series PLC - P7 . Tạo kết nối HMI Mitsubishi với PLC FX 👇
• How to connect GOT2000 HMI with MELSE...
8. How to Upload, Download and Monitor the PLC program via GOT - P8 | Download chương trình PLC qua HMI 👇
• Upload, Download and Monitor the PLC ...
9. GX Works3: Installation & Simulator - P9 I Cài đặt và chạy mô phỏng PLC Mitsubishi 👇
• GX Works3: Installation & Simulator -...
10. How to simulate GT Designer3 with GX Works2 - P10 | Kết nối GT Designer3 với GX Works2 qua mô phỏng 👇
• How to simulate GT Designer3 with GX ...
11. GX Works2: How to connect KEPServerEX with MELSEC-Q Series by ethernet driver - P11 👇
• GX Works2: How to connect KEPServerEX...
12. FX3U PLC: Communication Modbus RTU with E5CC Temperature Controller - P12 | Truyền thông Modbus RTU 👇
• FX3U PLC: Communication Modbus RTU wi...
13. How to connect WEINVIEW HMI with FX3U PLC - P13 | Tạo kết nối HMI WEINTEK với PLC FX 👇
• How to connect WEINVIEW HMI with FX3U...
14. MR Configurator2: How to Install, Read & Write parameters Servo Amplifier - P14 | MELSERVO-J4 👇
• MR Configurator2: How to Install, Rea...
15. How to connect Proface HMI with MELSEC-Q Mitsubishi PLC via Ethernet Port - P15 👇
• How to connect Proface HMI with MELSE...
16. Configure CC-LINK system MELSEC-Q PLC - P16 | Cấu hình và test mạng CC-LINK của PLC dòng Q 👇
• Configure CC-LINK system MELSEC-Q PLC...
Các bạn nhớ ủng hộ mình bằng cách nhấn Like và đăng ký kênh mình nha.
Nếu có yêu cầu gì thì comment bên dưới giúp mình .
Remember to support me by clicking Like and Subscribe to my channel.
If you have any questions, please comment below.
#ThuanAutomation
Thank You & Best Regard !!!
***********************************
☆ FOLLOW " Thuan Automation "
▶ Email : [email protected]
▶ Phone : +84 931359303
▶ Subscribe : https://bit.ly/2RKbVD3
▶ Facebook : / thuanautomatic
▶ Zalo : http://zaloapp.com/qr/p/hjzjeafqnsei
***********************************
© Bản Quyền Thuộc Về Kênh Thuan Automation
© Copyright by Thuan Automation Channel
⛔️ Do not Reup