If you're looking to install Klipper for your 3D printer, you've come to the right place 😎 ! In this tutorial, I'll show you how to install and configure Klipper for all 3D printers, even your Ender 3!
Installing Klipper on the Raspberry Pi can seem daunting, when in fact it's very simple! With this step-by-step guide, you'll learn how to flash Klipper, set up initial calibrations, and get fast results using MainsailOS.
If you're looking for configurations for your 3D printer, look below in the description 😉

#3dprinter #klipper #tutorial

Follow the guide!

👍 THUMB UP AND SUBSCRIBE 👍

As always, don't forget to subscribe to see the rest!

To follow me on the networks:
📲 INSTAGRAM @tomsbasement
📲 FACEBOOK   / rctruckstips  
📲 TIKTOK : @tomsbasementyt
📲 DISCORD :   / discord  
📧 MAIL [email protected] (for commercial proposals only)

⭐️ Products used in the video:
👉 Longer LK4 X
👉 Raspberry Pi (Rpi)

⭐️ Useful links from the video
👉 Raspberry Pi Imager: https://www.raspberrypi.com/software/

⭐️ Products used in the video:
👉 Sandisk Extreme MicroSD card: https://amzn.to/3ZNN1Uu
👉 Raspberry Pi 3B+ (Rpi 3B+)
👉 Longer LK4 X

⭐️ CONFIGURATIONS
⚠️ For Creality printers, rename the firmware other than just firmware.bin and change the name each time.

👉 Ender 3 PRO: https://github.com/Klipper3d/klipper/...

👉 Ender 3 V2: https://github.com/Klipper3d/klipper/...

👉 Ender 3 V2 NEO: https://github.com/Klipper3d/klipper/...

👉 Ender 3 S1/S1 Pro (there are two values to change in the configuration for the Pro): https://github.com/Klipper3d/klipper/...

👉 Creality CR10 Smart Pro: https://github.com/Klipper3d/klipper/...

👉 Alfawise U30: https://github.com/Klipper3d/klipper/...

👉 Anycubic Vyper: https://github.com/Klipper3d/klipper/...

👉 Anycubic Kobra Go: https://github.com/Klipper3d/klipper/...

👉 Artillery Sidewinder X2 (attention, it seems that the installation procedure is a bit different, it is described in the configuration file) : https://github.com/Klipper3d/klipper/...

👉 Artillery Sidewinder X1:    • Installer et configurer Klipper pour ...  

👉 Longer LK4 X: https://github.com/Klipper3d/klipper/...

👉 Prusa Mini Plus: https://github.com/Klipper3d/klipper/...

👉 Find a selection of configurations model by model here: https://www.rctruckstips.com/comment-...

⭐️ FULL LIST OF KLIPPER CONFIGURATION EXAMPLES: https://github.com/Klipper3d/klipper/...

Chapters:
00:00 Intro
00:57 Preparing the hardware
02:08 Installing Klipper on the SD card
05:40 Start up and first SSH connection
09:43 Preparing to compile Klipper
10:01 Preparation of the compilation (Longer LK4 X)
11:17 Preparing the configuration for an Ender 3 Pro
12:14 Preparing the configuration for the Ender 3 S1
12:56 Firmware compilation
13:30 Moving the compiled firmware
14:03 Flashing Klipper on your 3D printer
15:17 Adding the Klipper configuration
16:45 Adjusting the plate
18:49 Setting the Z offset
20:41 First test print
21:41 First print result
22:02 Conclusion
22:59 Outro

========================
Music :
"Dreams" - Bensound
"For Me" - Ketsa